PRODUCT

OTG Heavy Duty BCD and Regulator Hanger is especially design to hang your BCD and Din or Yoke regulator. It's made of sturdy Plastic material and strong enough to support the weight of your wet BCD and regulator together. The hook / wing design on both end is to prevent your BCD from sliding off and keep your BCD more secure. This hanger comes with the din thread and attachment point which can hold your Din or Yoke regulator. It's a good item to hold your BCD and regulator during drying and storage.

OTG Heavy Duty BCD and Regulator Hanger is especially design to hang your BCD and Din or Yoke regulator. It's made of sturdy Plastic material and strong enough to support the weight of your wet BCD and regulator together. The hook / wing design on both end is to prevent your BCD from sliding off and keep your BCD more secure. This hanger comes with the din thread and attachment point which can hold your Din or Yoke regulator. It's a good item to hold your BCD and regulator during drying and storage.

OTG Technical Scuba Diving Stainless Steel Single Tank Adapter with 2 Stainless Steel Buckle Tank Bands - Ideal for divers switch their harness system between double tank and single tank rigs or between backmount and sidemount configurations.

OTG Technical Scuba Diving 50 LBS Lift Bag is perfect for salvage projects or even better for use as a marking buoy for decompression or safety stops in the open water. The lift capacity of this bag is (50 lbs / 23kgs) and has a handle at the top and reflective tape on both sides. The open bottom one-way valve design will allow excess air to vent in the case of an uncontrolled ascent but prevent air loss at the surface. Made of durable nylon material in a high visibility Orange color. The Over Pressure Valve (OPV) is located at the top of the bag to rapidly remove air when needed but also serves to eliminate accidental over-inflation during ascent from expansion. It is a must-have accessory for every open ocean diver.

OTG Technical Scuba Diving Din To Yoke Cylinder Filling Adapter is for 200 / 300 Bar Din valve to filling with a standard Yoke filler up to 3,000 psi (200 bars). Just bring this adapter with you wherever you go, you can fill your Din cylinder from any dive operator even they only can fill the Yoke valve cylinder.

OTG Technical Scuba Diving Bellows Pocket have enough space to fit SMB, lift bag, safety reel, large finger spool or many other accessories. 2 bungee cord loop inside the main pocket to help secure item. Also there have an internal divider for stowing the dive notepads and the pocket flap with built-in accessory pocket. Two 1.25" wide nylon webbing strips along the back provide a secure fit on any 2" webbing. There are also one 2" wide nylon webbing strip to allow for slide it to 4" cummerbund. The heavy duty velcro closure keeps the pocket flap closed more securely.

OTG Scuba Diving Second Stage Regulator Quick Disconnect Adapter allows you to turn your second stage regulator into a quick disconnect device. Nowadays it is commonly used with normal second stage or full face mask system. Just simply to install the female end to any standard second stage regulator with 9/16"-18 UNF threads. And the nipple end is fit to connect to any standard BC quick disconnect adapter. This adapter is made by Marine Chrome Plated Brass and is completed 40% Nitrox ready. The working pressure is below 200psi and for low pressure use only.

OTG Technical Scuba Diving Din Cylinder Tank Pressure Checker is for the diver to check their tank pressure before the gear set-up. The reading range of this checker is from 0 - 5,000 psi (0 - 350 bars), and the diameter size of the pressure gauge is 2" (not included the rubber boot), it is easy to read. The pressure gauge is covered by rubber boot for much more security and the material of this checker is marine grade chrome plated brass. It has a bleed screw valve for easy to use and come with a Din thread plastic protector cap.

OTG Technical Scuba Diving Non-Directional Line Marker for Wreck or Cave Dive - Non-directional line marker mark a specific place on the line, but do not give directional information. They are preferred over line arrows for setting up traverses or circuits because they avoid the possibility of having directional markers on the line which could point away from the closest exit, which could be disastrous in an emergency. They are a must at jumps, especially jumps made from points at which no permanent marker has been installed. Placed on the outbound side of the jump, they confirm exit direction as divers return to the jump. This Rectangle marker is perfect for Diver to write down any information on the surface which they want.